Version Information: $Id: FAQ,v 1.7 2004/07/23 17:29:03 akool Exp $
Release Information: $Name:  $

Please see below for german version

ENGLISH:
Q: Is the analog-module of the Siemens DVB-C supported?
A: No because a driver for that module is still missing

Q: Does it work without any hardware-MPEG-decoder card?
A: Yes, but you cant see anything ;-)

Q: When compiling the plugin the error:
   "make[1]: *** No rule to make target `common/videodev2.h', needed by `player-analogtv.o'.  Stop."
   appears.
A: You should read (again) the README ;-)

Q: Picture and Sound - Bugs
A: Please use at least vdr-analogtv-0.9.0
   install the enclosed vdr-Patch (see the README)

Q: /var/log/messags fills up with
   Feb 28 23:11:11 tv vdr[12588]: ERROR: error in data stream!
A: Please install the enclosed vdr-Patch (see the README)

Q: No picture
A: Use xawtv once, then a picture should appear, or use V4L25

Q: No Sound
A: verify your Soundcard-setup at the plugin-settings
   Is there Sound with xawtv? If not: check The cable between TV-Card
   and Soundcard                
   If Yes: check The setting "Audiodevice" in the plugin setup

Q: Not Lip-synchronous
A: use at least vdr-analogtv-0.9.0, update to V4L2,
   use ALSA sound drivers

Q: The plugin quits with the error:
   "Sorry, this plugin requires an MMX enhanced CPU"
A: attach a modern CPU ;-)

Q: Picture too dark/bright, bad contrast, etc.
A: setupable in the Plugins-setup

Q: Bad radio reception
A: vary the frequencies in channels.conf

Q: The analog EPG does not work
A: check "/tmp/epg.err" for errors - mostly wrong channelnames

GERMAN:
Q: Wird das Analog-Modul der Siemens DVB-C unterstzt?
A: Nein, da es dafr bislang keinen Treiber gibt.

Q: Funktioniert es ohne Hardware-MPEG-Decoder-Karte?
A: Ja, aber man kann nichts sehen ;-)

Q: Beim kompilieren des Plugin erscheint die Fehlermeldung
   make[1]: *** No rule to make target `common/videodev2.h', needed by `player-analogtv.o'.  Stop.
A: Du solltest (nochmal) genau(er) das README lesen ;-)

Q: Bild- sowie Tonstrungen
A: bitte verwende mindestens vdr-analogtv-0.9.0
   installiere den beiliegenden vdr-Patch (siehe README)

Q: /var/log/messages quillt ber mit der Meldung
   Feb 28 23:11:11 tv vdr[12588]: ERROR: error in data stream!
A: bitte installiere den beiliegenden vdr-Patch (siehe README)

Q: Kein Bild
A: einmal xawtv benutzen, danach sollte ein Bild kommen
   oder V4L2 benutzen 

Q: Kein Ton
A: Soundkarteneinstellungen im Setup des Plugin berprfen
   Kommt mit xawtv Ton? Falls nein: Kabel zwischen TV-Karte und Soundkarte 
   berprfen. 
   Falls ja: Im Setup "AnalogTV Einstellungen" das Kapitel "Audioeinheit"
   berprfen

Q: nicht Lippensynchron
A: mindestens vdr-analogtv-0.9.0 verwenden, auf V4L2 updaten,
   ALSA-Soundtreiber verwenden

Q: Das Plugin beendet sich sofort wieder mit der Fehlermeldung
   "Sorry, this plugin requires an MMX enhanced CPU"
A: Modernere CPU einbauen ;-)

Q: Bild zu hell/zu dunkel, schlechter Kontrast etc.
A: ber "AnalogTV Einstellungen" einstellbar

Q: schlechter Empfang
A: Frequenzen in channels.conf variieren

Q: Das bernehmen des analogen EPG funktioniert nicht
A: "/tmp/epg.err" auf Fehlermeldungen untersuchen - meist falsche Sendernamen

Q: Es erscheint die Fehlermeldung
     Setting of Audio-Pid failed, 14:Bad address
     Cannot set Pids on PVR-card. analogTV giving up!
A: Dies ist ein Problem des aktuellen ckennedy ivtv-Treibers.
   Bitte in der "channels.conf" die Video-Pid auf 301, und die Audio-Pid
   auf 300 stellen, dann funktioniert es trotzdem
